- Show results for
- Share
The EMP Shield: Benefits, Working Principle & Installation Guide
Resource Description
Table Of Contents
- Introduction
- What Is the EMP Shield & What Are Its Benefits?
- How Does the EMP Shield Work?
- How to Install the EMP Shield on Your Vehicle?
- Final Thoughts
Introduction
In our unpredictable world, the need to safeguard your home, vehicle, generator, etc. against electromagnetic pulses (or EMPs) and lightning strikes is critical. These phenomena can potentially disrupt and permanently damage electronic components and systems.
What is an EMP? It is a brief burst of electromagnetic energy that can be caused by solar flares, nuclear explosions, etc.
What is the solution? The EMP Shield.
In this article, you will find out about the EMP Shield and its advantages, we will explain how it works and how to install it.
What Is the EMP Shield & What Are Its Benefits?
The EMP Shield (developed by EMP Shield Inc.) is the 1st EMP protection technology for an entire home & vehicle in the world tested to military & UL 1449 standards from ETL. EMP Shield products are made in the USA. Protect your home, car, generator, etc.
The EMP Shield can withstand over 40x EMP strikes without any degradation, which is impressive. This device has been rigorously tested at the Keystone Compliance laboratory, a federally approved & DOD testing facility. The testing process has demonstrated that the EMP Shield surpasses military EMP Protection device standards.
EMP Shield is a company that is committed to excellence in everything, it offers tested & proven solutions that meet & exceed customers’ needs and expectations.
BENEFITS
 |
 |
 |
| EMP Protection | Lightning Protection | Coronal Mass Ejection (CME) & Solar Flare Protection |
In case of emergency, the grid may be down, but with the EMP & Lightning Protection, your equipment & home will be functional. With the DC-12V-W EMP & Lightning Protection, for example, your vehicle will operate after EMP and you will be able to get home yourself and maybe save other people.
The Advantages of the EMP Shield
- Listed by the Department of Homeland Security
- One of the Fastest in the World
- Exceptionally Powerful
- Easy & Fast to Install
How Does the EMP Shield Work?
With the EMP Shield, your electronics & equipment connected to your electrical system will be protected. It is possible by shunting (shorting) the overvoltage coming in from the grid & the voltage surges collected within the home.
The EMP Shield will see the surge & protect the electrical system whether the source of electrons comes from within your home or from the grid. The SightSpeed™ technology reacts in less than 1 billionth of a second. This rapid response ensures that the overvoltage is drained away from your equipment before the voltage can rise to a damaging level.
How to Install the EMP Shield on Your Vehicle?
Let’s take a look at the installation process of the DC-12V-W EMP Shield - great EMP protection for vehicles.
The steps described below will be the same for most cars, trucks, four-wheelers, planes, boats, as well as motorcycles.
ATTENTION!
Electricity can be extremely dangerous and even fatal. It is strongly recommended that only certified electricians or mechanics install the EMP Shield. Do NOT touch the exposed positive side of the battery & the negative side of the battery simultaneously (or any piece of metal connected to the chassis because it could cause a spark/shock).
Follow the steps below to install your EMP Shield:
Step 1
Prepare a wrench (it is better to use a socket wrench) & identify the 3 wires attached to your EMP Shield:
Red Wire = Positive Wire (+)
Black Wire = Negative Wire (-)
Green Wire = Ground Wire (G)
Step 2
Find a spot inside the engine compartment for the installation of your EMP Shield. Note that you will need to be able to see the green light on the device. Make sure that the place is thoroughly cleaned so that the fastener bonds to the chosen spot without any problems.
Peel the plastic strips off the fastener & press the adhesive side to the place you chose.
Press & hold the device in place for approximately 15 seconds.
Step 3
Once you have positioned your EMP Shield in its place, measure the wire length needed to reach the positive and negative terminals on the battery of your vehicle. Wrap any excess wire & use small zip ties to keep the excess wire secured.
Step 4
Loosen and remove the nut from the positive terminal as this is where the red wire will connect. Often, a battery will show red or the plus sign to indicate where the positive terminal is. Place the connector of the red wire on the positive terminal and tighten the nut to keep the wires in place.
This is how it should look if you’ve properly installed the positive wire.
Step 5
Now, let’s install the ground wire (the green one). Note that the installation point for it must be no less than four linear feet from the battery negative. In addition, make sure that the green grounding wire is connected to a dedicated bolt.
Do not use any bolt on your vehicle that is grounding other electrical systems, as this can interfere with the proper functioning of your EMP Shield.
The ground wire will connect to the chassis. This wire is installed similarly to the positive wire. Loosen the nut, place the wire in the correct location, and then tighten the nut securely.
Step 6
Finally, let’s install the negative wire (the black one). It will go on the negative side of the battery. Often, the minus sign is used as its symbol. To install this wire, you need to loosen the nut, place the connector down, and then tighten the nut firmly.
If you have installed everything correctly, you will see the green light on the device, which means that it is actively protecting your vehicle.
Final Thoughts
Shielding from EMP is important, no doubt about that! Hopefully, after reading this article, you know the benefits of using EMP protectors, their working principle, and the installation process. EMP Shields are made with the user in mind, they are reliable and easy to use. There are many options available.
If you are looking for your car EMP protection/EMP car protection/EMP protection for cars, the EMP Shield is an excellent choice! Electromagnetic pulse shielding is an effective way to protect your vehicle. A great EMP Shield for cars is the DC-12V-W model.
On our website, you can also get many other EMP Shield products, for example, pay attention to the EMP protection for generators so that you can make your generator an EMP proof generator.
If you are in search of an EMP Shield for home use/EMP protection for home/home EMP protection, there are great Home EMP & Lightning Protection + CME Defense options: SP-SP-120-240-W & SP-120-240-RL. Protect your home from EMPs effectively!
In addition, you can choose from EMP Shield Solar Wind System EMP Protection. EMP Shield also offers Radio EMP Protection. There are various EMP Shields, find the right one for your application.
Shop with Prime Buy, choose the best EMP shielding solution, and your electronics and equipment will be protected from EMP and lightning!